Serial Number Check Up

LUX-RC MINION R2 Flashlight

Build Date:     Dec 2019

Program with:   NXS R1

LE Hardware:    371 RES-26749
LE Firmware:    371D R1.3.1 ID151 041019 [FL33]
LE Peak Output: 32W (3.2A per each LED)
LE Carry Sens:  MVS0608.02

LED Type:       3UP Samsung LH351D HI-CRI RA95 
LED Bin:        4000K F2 T7 Q2
Orig. LED Num:  SPHWHTL3DA0GF2T7Q2
Aux LED:        Amber 611nm

SPE1:           U2 BU7495HFV 5MHZ 5V/US
SPE2:           D2 1SS400CST2RA (EXP.)
SPE3:           L1 XEL4020-222MEC

LED Optics:     CARCLO 10507
Window:         AR Sapphire Crystal YHOIF-JS20170407
Options:        Polished Stainless Steel

Order Made:     December 3, 2019
Order No:       2801
Order Country:  Russia
First Owner:    Michael K.


========= RELEASE NOTES =========

R1.0 Apr 15, 2015 
  - Beta board for OR, power pulse UI (requires special 
    web timing)

R1.1 Jun 1, 2015
  - Programming timing fixed to support all screens
  - 0.7s default mode switch time, "222" factory PIN

R1.2 Nov 17, 2015 
  - The voltage tracking/state machine full redesign
  - 1S/2S voltage display
  - Bat safety switchover (up to ~50mOhms internal res)
  - Hybrid memory revision. Selection is saved after 2s
  - MOM: on/off, mode switching, three special modes and
    programming, lock, program with holding mom, FL33 RGB

R1.2 Dec 18, 2015 
  - The battery lock leak fixed

R1.2 Dec 31, 2015 
  - The PIN enter click is set to 1/2s limit

R1.2.1 Feb 22, 2016
  - Temperature and bounce reading fixes (stepdown issue)
  - Extra low mode (signal) switching fix (decay monitor)
  - Low-battery occasional mode switchover fix
  - 1S heavy load surge detector added. Steps down to 3W
  - Access voltage meter with MOM (lock and hold)
  - Cap discharge optimization (mode switching improvement)
  - FL33 RGB indicator fix
  - 8ms temperature reading (leads to web app re-calibration)
  - Bat. fail/lock: 7-10uA leak, waits for battery swap
  - OVP: overvolt. check on start, no runtime checking

R1.2.2 Feb 24, 2016
  - mode saving to EEPROM fixed (FL_NOTSAVED)

R1.2.3 Mar 7, 2016 
  - 481 service PIN added: on/off the standby locator

R1.2.4 Mar 22, 2016
  - "No memory" bug fixed

R1.2.5 Apr 27, 2016
  - Service PIN fix: use 381 to control the standby locator

R1.2.6 Jun 27, 2018
  - Bug fix: the startup voltage meter accuracy and tolerance edited
  - Mode adjust flag removed (affects the mode switching)

R1.2.7 Nov 13, 2018

R1.2.8 Jun 25, 2019
  - Motion sensing (PIN 382 to control the MS on/off, fatory is off)
  - PWRTE configuration changed (memory fail fix)
  - Service PIN status indicator added

R1.3 Jun 27, 2019  
  - Slow/fast motion sensor configuration: PIN 383
  - Stepdown limit set to 100mW approx.
  - Prog memory protection added (memory fail fix)

R1.3.1 - Mom button is now compatible with motion sensing (FL33 fix)