LUX-RC ARTIFACT 2020 Flashlight Build Date: 2020 Q2 Assembly: Kris Gr. Program with: NXS R2 LE Hardware: 372 RES-1216109 RED LE Firmware: 371-372 V2.0 150420 LE Peak Output: 32W (3.2A per each LED) LE Carry Sens: MVS0608.02 LED Type: 6UP 2S3P CREE XD16 LED CCT: 4000K LED P/N: XD16AWT-H-5D0-S30-0B-0002 Aux LED: AMBER 611NM STD LED Optics: 10507 Narrow Clear Window: AR Sapphire Crystal YHOIF-JS20170407 Body: Glazed Alumina TIGAR 20160806A Artist: Lisa Kurochkina aka Qrochka Theme: Space Blue Order Made: May 20, 2020 Order No: 2867 Order Country: China First Owner: M. ========= RELEASE NOTES ========= R1.0 Apr 15, 2015 - Beta board for OR, power pulse UI (requires special web timing) R1.1 Jun 1, 2015 - Programming timing fixed to support all screens - 0.7s default mode switch time, "222" factory PIN R1.2 Nov 17, 2015 - The voltage tracking/state machine full redesign - 1S/2S voltage display - Bat safety switchover (up to ~50mOhms internal res) - Hybrid memory revision. Selection is saved after 2s - MOM: on/off, mode switching, three special modes and programming, lock, program with holding mom, FL33 RGB R1.2 Dec 18, 2015 - The battery lock leak fixed R1.2 Dec 31, 2015 - The PIN enter click is set to 1/2s limit R1.2.1 Feb 22, 2016 - Temperature and bounce reading fixes (stepdown issue) - Extra low mode (signal) switching fix (decay monitor) - Low-battery occasional mode switchover fix - 1S heavy load surge detector added. Steps down to 3W - Access voltage meter with MOM (lock and hold) - Cap discharge optimization (mode switching improvement) - FL33 RGB indicator fix - 8ms temperature reading (leads to web app re-calibration) - Bat. fail/lock: 7-10uA leak, waits for battery swap - OVP: overvolt. check on start, no runtime checking R1.2.2 Feb 24, 2016 - mode saving to EEPROM fixed (FL_NOTSAVED) R1.2.3 Mar 7, 2016 - 481 service PIN added: on/off the standby locator R1.2.4 Mar 22, 2016 - "No memory" bug fixed R1.2.5 Apr 27, 2016 - Service PIN fix: use 381 to control the standby locator R1.2.6 Jun 27, 2018 - Bug fix: the startup voltage meter accuracy and tolerance edited - Mode adjust flag removed (affects the mode switching) R1.2.7 Nov 13, 2018 R1.2.8 Jun 25, 2019 - Motion sensing (PIN 382 to control the MS on/off, fatory is off) - PWRTE configuration changed (memory fail fix) - Service PIN status indicator added R1.3 Jun 27, 2019 - Slow/fast motion sensor configuration: PIN 383 - Stepdown limit set to 100mW approx. - Prog memory protection added (memory fail fix) R1.3.1 Oct 4, 2019 - Mom button is now compatible with motion sensing (FL33 fix) R2.0 Mar 26, 2020 - ONECELL asm config: 2S check added (2S is not supported by ONECELL) - SHORT PIN 4: memory file selector (1-2-3-4) - PIN 111: runs voltage meter (MOM UI: hold locked button) - PIN 112 and 222: programming (hardcoded PINs) - PIN 113: battery tester (five star rating under the load, 0.15V per star) - All service PINs mask 33X, where X=1..7. Color and code confirmation added. White is ON. Red is OFF. Number of flashes is X (i.e. double red flash means 332 is OFF) - PIN 311: show service bits (red - OFF, white - ON) - PIN 331: standby and zero mode locator beacon: ON/OFF - PIN 332: motion sensing ON/OFF (factory is OFF) - PIN 333: motion sensing slow/fast timing profile - PIN 334: 8 mode/4+4 mode (factory is 8 modes) - PIN 335: zero mode ON/OFF (factory is OFF) - PIN 336: double click action (backward / last mode) - PIN 337: PPUI double click ON/OFF - Motion sensing: false-positive filter added, level 4 - MOM UI: 4th instant access mode (afterburning) - MOM UI: double-click action: mode step back / hop to final mode - Beacons rethinked: single red for standby and zero mode double red for motion tracking sleep mode - MOM UI: 4-click lock only from standby - MOM UI: endless looping in mode/special selection (mom hold) - PIN input: faster input, 1/2s gap between "figures" - Double-click in final mode returns to the original mode - MOM UI: double-click from standby jumps to the final mode - MOM UI: click-click-click-hold from standby to change file